La Speedmeter Gear Electric Gear 39 Teeth for 4 L60
700R4 Speedometer Drive Gear, #54X.
$ 12.00
- Description
- Additional information
- Reviews (0)
Description
#54X. Speedometer drive gear, comes in fifteen, 17, xviii or 19 tooth. (From left to right: 15 Tooth | 17 Tooth | eighteen Tooth | xix Molar)
Speedometer Figurer, Click Here
Main Speedometer Gear Page CLICK Here
Speedometer Calibration Variables such every bit the vehicle's axle ratio and tire diameter bear upon the accuracy of the speedometer. The post-obit speedometer bulldoze gears and driven gears are available for the 700R4 / 4L60 transmissions. Most cars and trucks with low rear finish ratios volition take a 15 molar drive gear. There are two driven gear housings, 1 for 34 through 39 tooth driven gears and one for 40 through 45 tooth driven gears. Expect a t the bottom of the speedometer face for the numbers 940, 960, chiliad, or 1020. These numbers are the number of revolutions the speedometer cable must plow in 1 mile of travel. Your speedometer may or may not show a number. Most speedometer from 1965 on use k.
Twelve speedometer driven gears are available for the 700R4 / 4L60 transmissions to calibrate the speedometer with various axle ratios and tire diameters. The number on the driven gear housing must friction match the number of teeth on the driven gear. Unless driven gears with more 45 teeth and / or drive gears with fewer than xv teeth become available, information technology will be incommunicable without using a ratio adapter to accept an accurate speedometer with rear end gear ratios lower (higher numerically) than 4.10:ane, unless 27 inch or larger tires are installed.
To determine your tires truthful diameter in relation to determining what speedometer gears you need, measure from the ground upwardly to the centre of the axle then multiply by two. The actual run out of the tire can exist as much as 2 to 3 inches less than what the circumference of the tire measures. In effect your tire has ii diameters.
To determine your rear cease ratio, raise both tires off of the ground, plow both tires at the aforementioned fourth dimension one complete plow, at the same time count the turns of the drive shaft, this is your ratio.
With fifteen Tooth Bulldoze Gear | ||
Beam Ratio | Tire Peak | Driven Gear Teeth |
4.56 | 33 | 42 |
4.56 | 35 | 39 |
4.10 | 26 | 45 will work, but will read about 3 MPH fast at 50 MPH. |
4.10 | 27 | 45 |
4.ten | 28 | 44 |
4.10 | 29 | 43 |
4.10 | thirty | 41 |
iv.10 | 31 | twoscore |
four.ten | 33 | 38 |
4.x | 35 | 35 |
3.73 | 26 | 43 |
three.73 | 27 | 42 |
3.73 | 27 ane/2 | 41 |
three.73 | 28 | twoscore |
iii.73 | 29 | 39 |
3.73 | 30 | 38 |
3.73 | 31 | 36 |
With 17 Molar Drive Gear | ||
Axle Ratio | Tire Height | Driven Gear Teeth |
3.73 | 28 | 45 |
three.73 | 29 | 44 |
3.42 | 26 | 45 |
three.42 | 26 1/ii | 44 |
3.42 | 27 | 43 |
three.42 | 28 | 42 |
With xviii Molar Bulldoze Gear | ||
Beam Ratio | Tire Height | Driven Gear Teeth |
3.23 | 26 | 45 |
3.23 | 26 1/two | 44 |
three.23 | 27 | 43 |
3.23 | 28 | 42 |
Count speedometer drive gear teeth from the end, click here.
Additional information
Weight | 1 lbs |
---|---|
Dimensions | four × 4 × 3 in |
Types | 15 Tooth, 17, eighteen, 19 Tooth, 34 to 39 Tooth, forty to 45 Tooth |
Only logged in customers who have purchased this production may leave a review.
DOWNLOAD HERE
La Speedmeter Gear Electric Gear 39 Teeth for 4 L60 UPDATED
Posted by: nancywinget.blogspot.com
Comments
Post a Comment